The most effective method to Install Blown In Attic Insulation

Blown-in-attic-insulation (1)



I have quite recently finished an expansion to my home. I’ve heard that Blown in attic insulation is better compared to batts since it covers the joists totally and leaves no open regions. Do you have any DIY ideas?




Indeed you are right. Blown in attic insulation is better than batts when introduced appropriately as it improves.


First you really want to quantify your storage room region that you anticipate protecting. Most lofts require a worth of R-30, R-38 or R-49, contingent upon your environment and area. When you know the area of your storage room you can decide how much protection you’ll require by straightforward looking on the diagram situated on the pack of protection.

Before you begin you should figure out what materials you will require. Expecting your home has recessed lights, roof and washroom fans and eave vents you will require the accompanying instruments and materials:


Free Fill Insulation

Cardboard Baffles


Channel Tape

Staple Hammer and Staples

Utility Knife

Stepping stool


Blown in attic insulation Machine (Available at your neighborhood rental store)


The storage room will require planning before you can really blow protection into it. Ensure you are wearing a residue cover, defensive goggles and a long sleeve shirt. Recessed lights should have blazing introduced around them leaving an open space of no less than four crawls from the glimmering to the light. Utilizing a utility blade, cut a piece of glimmering of the right length and structure it into a chamber shape, protecting the edge with pipe tape. Place over recessed light leaving a four inch open region. This takes into account the intensity to get away. Utilize a similar cycle for any vented kitchen or washroom fans in the upper room region.


The subsequent stage is confusing. This is an errand no one appreciates. The puzzles need to be introduced by utilizing your staple mallet and introducing them where the roof joists meet with rooftop rafters. Ensure you just introduce the confounds over the vents and that they are sufficiently high so the vents will not get covered with protection. Now that you’ve been introduced you should move out of the storage room and give you back a truly necessary rest.


The following stage of readiness is to make a dam around the storage room access opening. The simplest way is to cut a couple of additional cardboard puzzles into lengths of around 4 creeps over how much protection you anticipate introducing. Just staple them around the borders of the entrance opening. This will consider a uniform profundity in the protection you are blowing in.


So you don’t need to continue to slither all through the storage room. It’s ideal to have someone else outside assisting you with stacking the protection blowing machine. Here’s a clue: If you’re utilizing fiberglass protection, have your partner add about some water per sack, spreading it way too after it’s stacked into the machine. This will assist with chopping down friction based electricity when you are blowing the protection and it will set down more equally while introducing it. After the sack of protection is stacked into the container it will require a few minutes before the following pack is required. Try not to allow your assistant to be sluggish. Have him get on the stepping stool and haul an abundance hose out of the loft for you so you don’t get tangled in it.


I’ve found blowing protection into the storage room is a straightforward cycle. Begin and the furthest finishes of the loft. Going this way ensures its level and smoothness. Try to get all regions of the loft and fill no vents or recessed light regions. Take a measuring tape with you and check the levels every so often. For instance, if you’re introducing a R-38 of fiberglass protection you would believe that it should gauge 16 inches down. As you work your direction back close to the loft access ensure your aide is moving that abundance hose. At the point when you get to around 6 feet from the entrance opening stop the machine so you can get on the stepping stool. When on the stepping stool complete the process of introducing, making a point to bring the level equitably against the dam you recently fabricated.

The last step is to put a piece of batt protection in the entrance opening and painstakingly set up the storage room opening cover back. Presently you’re done! Avoid that loft however much as could be expected starting here as free fill protection that has been stepped on or squashed loses its R esteem.


The Pros and Cons of Blown Attic Insulation


Assuming you are building your fantasy home, or simply revamping your ongoing one you need the task finished right. You need no curve balls or accidents or unexpected bills not too far off on the grounds that something was not done well or perhaps it simply wasn’t the right material to make it happen. There probably won’t be a short summary of all aspects of home redesign, however there are a couple of things you ought to be familiar with blown upper room protection.


There are a great deal of Blown in attic insulation assortments out there from inflexible froth boards to fiberglass covers to blown loft protection. To go with the right decision for yourself as well as your home you must investigate as needs be. Converse with your worker for hire as well, he may not know how to protect your home with the materials you need to be utilized. Continuously know your decisions so you understand what the advantages and disadvantages are of every item. Blown loft protection is the most well-known kind of free fill storage room protection accessible. As such it very well may be an extraordinary defender of your home and venture. Blown in attic insulation comes in one of two material sorts, either fiberglass or cellulose. Blown upper room alludes to how the material is introduced, ordinarily with a huge machine that in a real sense “blows’ ‘ the protection all around the surfaces of the loft.



  • Blown storage room protection is the most well-known and furthermore one of the simplest to introduce. Most project workers know how to finish this work.
  • It is likewise the most economical of all of the protection types.
  • Establishment is quick, requiring around 2 hours relying upon the size of the upper room.
  • For added protection, batt protection can be introduced over top of blow storage room protection, however it will cost more.
  • Blown in attic insulation covers everything, leaving not many holes.


  • The r-factor (proportion of warm obstruction) in blown loft protection is the least of all protection types.
  • Since it is challenging to blow the protection consistently across the loft customarily the r-factor changes extraordinarily in any event, when introduced accurately.


One thing to recollect is dependably check to ensure that your administration project worker is giving you what he guaranteed and what you paid for. To consider the worker for hire responsible you ought to ensure you get your work done. Something most frequently held back on in home development or redesigns is blown storage room protection. Frequently they make how much Blown in attic insulation look right by simply turning the machine they are utilizing to introduce the material up to a higher setting to “cushion” it. Neglecting to protect your storage room can bring about energy misfortune and a much higher energy bill for you that will amount to the expense of fixing the issue when it ought to have been done squarely in any case. The right establishment of any protection is significant to getting a good deal on your energy bill.


Our Community Contributions